Trabajo Fin de Grado
Diseño de máquina cortadora de discos de chapa
Autor/es | Rosa Asencio, Julio Darío de la |
Director | Estévez Urra, Aída
![]() ![]() ![]() ![]() ![]() |
Departamento | Universidad de Sevilla. Departamento de Ingeniería Mecánica y de Fabricación |
Fecha de publicación | 2017 |
Fecha de depósito | 2017-03-03 |
Titulación | Universidad de Sevilla. Grado en Ingeniería de Tecnologías Industriales |
Resumen | Este documento se centrará en el análisis y diseño para posterior construcción de la estructura de fijación y soporte del mecanismo de corte, de una máquina de corte de chapa por cizalladura, que cortará chapas de metal ... Este documento se centrará en el análisis y diseño para posterior construcción de la estructura de fijación y soporte del mecanismo de corte, de una máquina de corte de chapa por cizalladura, que cortará chapas de metal de distinto diámetro, que será regulable, en forma circular. Se tratará en este trabajo la deformación plástica en chapa, así como las características del diseño a tratar. La parte de la máquina encargada del corte se encuentra en el “Diseño del mecanismo de corte para máquina cortadora de discos de chapa”, por Carlos Daza Pelegrina [21]. El análisis y el diseño completo de la máquina se realizará en conjunto con este documento. Las medidas del mecanismo de corte estarán ya definidas, pero se realizará un proceso de rediseño posterior si fuese necesario, así como las medidas del resto del diseño de la máquina. Este trabajo tratará con profundidad la parte de la fijación, el ajuste del diámetro a cortar, el apoyo del sistema de corte, la estructura y el apoyo de la máquina a la superficie donde se vaya a situar. Se incluye un diseño pensado, por su simplicidad, para la construcción del mismo con recursos y medios limitados. Las medidas serán proporcionales al tamaño de la máquina, y se dará un diseño estándar de la misma para el corte de chapas correspondiente a las medidas que serán necesarias obtener, siendo la máquina escalable pudiendo ampliarse su rango de trabajo si se aumentase o disminuyese su tamaño This work will focus on the analysis and the design of the elements from the structure, the anchorage and the holding mechanism for the cutting process of metal sheets in a circular shape, with different diameters that ... This work will focus on the analysis and the design of the elements from the structure, the anchorage and the holding mechanism for the cutting process of metal sheets in a circular shape, with different diameters that will be posible to regulate; in order to have the possibility of building it in any moment on the future. This document will include the necessary information about the plastic deformation in steel sheets to face the design, as well as its characteristics. The cutting parts of the machine are located in “Diseño del mecanismo de corte para máquina cortadora de discos de chapa”, por Carlos Daza Pelegrina [21], and the complete analysis and design of this machine will be done along with this document. The measures of the cutting mechanism will be given, same as the desired diameters for the steel sheets, but a redesign could be done if necessary in order to complete the rest of the machine‟s design. This document will include full details about the sheet-fixing part, the adjustment of the diameter to be cutted, the holding system for the cutting mechanism, the structure and the anchorage. For its simplicity, this design is though for the construction of the machine with limited resources. The measurements will be proportional to the size of the machine, since we will give a standard design of the same for the machining of sheets corresponding to the measures that have been entrusted to us. |
Ficheros | Tamaño | Formato | Ver | Descripción |
---|---|---|---|---|
TFG de Julio Dario de la Rosa.pdf | 6.463Mb | ![]() | Ver/ | |