Buscar
Mostrando ítems 21-30 de 33
Artículo
Reactive flash sintering of SrFe12O19 ceramic permanent magnets
(Elsevier, 2022)
Reactive flash-sintering technique has been used in order to obtain strontium ferrite magnets from a mixture of SrCO3 and Fe2O3 commercial powders. This technique allows preparing sintered SrFe12O19 at a furnace temperature ...
Artículo
Mechanical and electrical properties of low SWNT content 3YTZP composites
(Elsevier, 2015)
Fully dense 3mol% Y2O3-ZrO2 (3YTZP) composites with low single wall carbon nanotube content (0.5, 1 and 1.5vol% SWNT) were prepared by colloidal processing and spark plasma sintering (SPS). SWNT were distributed at ceramic ...
Artículo
R-curve Evaluation of 3YTZP/Graphene Composites by Indirect Compliance Method
(Elsevier, 2023)
This work addresses the crack growth resistance of 3 mol% Yttria-doped Tetragonal Zirconia Polycrystalline (3YTZP) spark-plasma sintered (SPS) composites containing two types of graphene-based nanomaterials (GBN): exfoliated ...
Artículo
Improvement of Vickers hardness measurement on SWNT/Al2O3 composites consolidated by spark plasma sintering
(Elsevier, 2014)
Dense alumina composites with different carbon nanotube content were prepared by colloidal processing and consolidated by Spark Plasma Sintering (SPS). Single-wall carbon nanotubes (SWNTs) were distributed at grain boundaries ...
Artículo
Flame confinement in biomass combustion systems for particles abatement
(Elsevier, 2022)
This work explores the use of open-pore, inert ceramic foams with different pore sizes as particle abatement systems in small biomass combustion systems. Porous foams made of silicon carbide with pore sizes 10 to ...
Artículo
Structural Relaxation in Fe(Co)SiAlGaPCB Amorphous Alloys
(Elsevier, 2014)
The structural relaxation of multicomponent Fe(Co)SiAlGaPCB amorphous alloys was investigated calorimetrically for annealed samples over a wide temperature range below the glass transition temperature. Upon heating, the ...
Artículo
Enhanced magnetocaloric properties of annealed melt-extracted Mn1.3Fe0.6P0.5Si0.5 microwires
(MDPI, 2022)
: The highly regarded Fe2P-based magnetocaloric materials are usually fabricated by ball milling, and require an additional extended annealing treatment at high temperatures (at temperatures up to 1423 K for several hours ...
Artículo
Magnetic and Structural Characterization of Mo-Hitperm Alloys with Different Fe/Co Ratio
(Elsevier, 2011)
The influence of the Co content on the microstructure and magnetic behaviour of a series of amorphous and nanocrystalline (FeCo) 79Mo8Cu1B12 alloys is reported. Changes in the magnetic properties provoked by the microstructural ...
Artículo
Influence of the porosity and type of bioglass on the micro-mechanical and bioactive behavior of coated porous titanium substrates
(Elsevier, 2021-01)
In this study, the best equilibrium among adherence, micro-mechanical properties and coating bioactivity of bioactive glasses (45S5 and 1393) on porous titanium substrates has been explored and their potential uses for ...
Artículo
Scratch, Fretting, and Sliding Wear of a ZrB2–hardened Zr3Al2 Intermetallic–ceramic Composite
(Elsevier, 2023)
The unlubricated wear behaviour of a very recently developed ZrB2–hardened Zr3Al2 intermetallic–ceramic composite was investigated for the first time. In particular, tribological tests of scratch, fretting, and sliding ...