Buscar
Mostrando ítems 1-10 de 31
Ponencia
Estudio preliminar de los parámetros de fabricación en las propiedades finales de piezas de titanio comercialmente puro con geometrías sencillas producidos mediante la técnica de “additive manufacturing”
(3 ciencias. Área de Innovación y Desarrollo,S.L., 2019)
La necesidad de fabricar piezas de geometrías complejas empleando materiales ligeros con altas propiedades, en el sector aeroespacial conlleva al uso de técnicas cada vez más flexibles y con mayor complejidad técnica. ...
Artículo
Effect of HVOF processing parameters on Cr₃C₂-NiCr hard coatings deposited on AISI 4140 steel
(Elsevier, 2023-03)
High Velocity Oxygen Fuel (HVOF) thermal spray coating is a deposition process that is widely employed at present to improve surfaces and the remanufacturing of components subject to severe wear, offering an alternative ...
Ponencia
Fabricación mediante innovadoras técnicas pulvimetalúrgicas de materiales compuestos de matriz ligera
(Editorial Área de Innovación y Desarrollo, 2016)
Hoy en día el interés por desarrollar nuevos materiales que satisfagan las necesidades tecnológicas, conlleva a un estudio continuo en la innovación de los procesos de fabricación. La ventaja que ofrecen las técnicas ...
Artículo
Processing by Additive Manufacturing Based on Plasma Transferred Arc of Hastelloy in Air and Argon Atmosphere
(MDPI, 2020-01)
This research was carried out to determinate the effect of the atmosphere processing conditions (air and argon) and two specific thermal treatments, on the properties of specimens made from the nickel-based alloy Hastelloy ...
Artículo
Study of the Influence of TiB Content and Temperature in the Properties of In Situ Titanium Matrix Composites
(MDPI, 2017-10-27)
This work focuses on the study of the microstructure, hardening, and stiffening effect caused by the secondary phases formed in titanium matrices. These secondary phases originated from reactions between the matrix and ...
Artículo
Analysis of the Influence of Starting Materials and Processing Conditions on the Properties of W/Cu Alloys
(MDPI, 2017)
In this work, a study of the influence of the starting materials and the processing time used to developW/Cu alloys is carried out. Regarding powder metallurgy as a promising fabrication route, the difficulties in ...
Artículo
Influence of Processing Conditions on the Mechanical Properties of 17-4PH Specimens Produced by Additive Manufacturing
(MDPI, 2022-11)
The purpose of this research is to study the influence of the processing conditions that affect the final behaviour of specimens made from a 17-4PH composition powder without the necessary thermal treatment to be considered ...
Artículo
Influence of sintering temperature on the microstructure and mechanical properties of in situ reinforced titanium composites by inductive hot pressing
(MDPI AG, 2016-11)
This research is focused on the influence of processing temperature on titanium matrix composites reinforced through Ti, Al, and B4C reactions. In order to investigate the effect of Ti-Al based intermetallic compounds on ...
Artículo
Nanocrystalline Al Composites from Powder Milled under Ammonia Gas Flow
(Hindawi Publishing Corporation, 2014)
The production of high hardness and thermally stable nanocrystalline aluminium composites is described. Al powder was milled at room temperature in an ammonia flow for a period of less than 5 h. NH3 dissociation during ...
Artículo
Comparative study of the behaviour of several reinforcement materials in titanium matrix produced by Rapid Sinter Pressing Manufacturing
(Editorial CSIC, 2022-12)
Regarding titanium matrix composites (TMCs), their properties strongly depend on the reinforcement material employed for their manufacturing; this may lead to a multitude of investigations on TMCs. Considering the diverse ...