Buscar
Mostrando ítems 1-10 de 17
Artículo
Microestructura y propiedades mecánicas de conductores protónicos de alta temperatura crecidos por fusión de zona flotante
(2004)
Se han estudiado conductores protónicos de alta temperatura (CPAT) fabricados por fusión de zona flotante asistida por láser (SrCe0.9Y0.1O3-δ , SrCe0.8Y0.2O3-δ , SrZr0.9Y0.1O3-δ , SrZr0.8Y0.2O3-δ , Sr3 (Ca1.18Nb1.82)O9-δ ...
Artículo
High-temperature mechanical behavior of proton-conducting yttrium-doped barium zirconate perovskite
(Elsevier, 2021-02)
The high-temperature mechanical properties of yttrium doped barium zirconate obtained by two different routes are reported in this work. Polycrystals with composition BaZr0.85Y0.15O2.925 have been fabricated from nanopowders ...
Artículo
Effect of high SWNT content on the room temperature mechanical properties of fully dense 3YTZP/SWNT composites
(Elsevier, 2014)
This paper is devoted to correlate the microstructure and room temperature mechanical properties of single-wall carbon nanotube (SWNT) reinforced 3. mol% yttria stabilized tetragonal zirconia with high SWNT content (2.5, ...
Artículo
Bioactivity of wollastonite/aerogels composites obtained from a TEOS-MTES matrix
(Springer Nature, 2008)
Organic-inorganic hybrid materials were synthesized by controlled hydrolysis of tetraethoxysilane (TEOS), methyltrimethoxysilane (MTES), synthetic wollastonite powders and polydimethylsiloxane (PDMS) in an ethanol solution. ...
Artículo
Powder-metallurgy fabrication of ZrB2-hardened Zr3Al2intermetallic composites by high-energy ball-milling and reactive spark-plasma sintering
(Elsevier, 2022)
A powder metallurgy route combining high-energy ball-milling (HEBM) of elemental powders and reactive spark-plasma sintering (SPS) is proposed for the controlled fabrication of novel composites based on a Zr-Al intermetallic ...
Artículo
Enhanced carbon nanotube dispersion in 3YTZP/SWNTs composites and its effect on room temperature mechanical and electrical properties
(Elsevier, 2016-10)
In this work, several modifications of the colloidal processing technique and spark plasma sintering (SPS) to prepare yttria tetragonal zirconia composites (YTZP) with single walled carbon nanotubes (SWNT) have been ...
Artículo
Reinforced silica-carbon nanotube monolithic aerogels synthesised by rapid controlled gelation
(Springer Nature, 2018)
This work introduces a new synthesis procedure for obtaining homogeneous silica hybrid aerogels with carbon nanotube contents up to 2.50 wt.%. The inclusion of nanotubes in the highly porous silica matrix was performed by ...
Artículo
Fabricación y propiedades del carburo de silicio biomórfico: maderas cerámicas
(2002)
En los últimos años se ha puesto de manifiesto un considerable interés en la fabricación y optimización de materiales de microestructura biomórfica. En particular, la fabricación de cerámicas biomórficas es especialmente ...
Artículo
Mechanical and electrical properties of low SWNT content 3YTZP composites
(Elsevier, 2015)
Fully dense 3mol% Y2O3-ZrO2 (3YTZP) composites with low single wall carbon nanotube content (0.5, 1 and 1.5vol% SWNT) were prepared by colloidal processing and spark plasma sintering (SPS). SWNT were distributed at ceramic ...
Artículo
Creep study on alumina and alumina/SWCNT nanocomposites
(Elsevier, 2018)
Alumina and alumina/SWCNT nanocomposites have been sintered by spark plasma sintering, obtaining relative densities higher than 99%. Microstuctural characterization revealed a grain microstructure in the submicron range, ...