Author profile: Centeno Báez, Gabriel
Institutional data
| Name | Centeno Báez, Gabriel |
| Department | Ingeniería Mecánica y Fabricación |
| Knowledge area | Ingeniería de los Procesos de Fabricación |
| Professional category | Catedrático de Universidad |
| Request | |
 |
|
Statistics
-
No. publications
37
-
No. visits
3699
-
No. downloads
4235
| Publications |
|---|
Article
 Assessing Formability and Failure of UHMWPE Sheets throughSPIF: A Case Study in Medical Applications
(MDPI, 2023)
This work presents a comprehensive investigation of an experimental study conducted on ultra-high molecular weight ... |
PhD Thesis
 Formability and failure of polymeric sheets: experimental assessment and medical applications
(2023)
Durante las últimas décadas, el paradigma de la Industria 4.0, que se dirige hacía procesos flexibles, de baja-media ... |
Article
On the effective peek application for customized cranio-maxillofacial prostheses: An experimental formability analysis
(Elsevier, 2023)
Single Point Incremental Forming (SPIF) is a dieless and flexible forming technology that allows performing complex shapes ... |
Final Degree Project
Análisis experimental de piezas tipo fabricadas mediante modelado por deposición de fundido (FDM) en la impresora 3D ULTIMAKER S5
(2023)
La fabricación aditiva ha experimentado en los útlimos años un gran desarollo y es por eso que se presenta la oportunidad ... |
Article
Experimental investigation of polycarbonate sheets deformed by SPIF: formability, micro-mechanisms of failure and temperature analysis
(Elsevier, 2023)
This article presents an experimental research performed on a polycarbonate sheet deformed by single point incremental ... |
| Article |
Presentation
Numerical Modelling of Conventional and Incremental Forming of Thin-Walled Tube
(Trans Tech Publications Ltd., 2022)
This study presents a numerical analysis of the tube expansion process by conventional tube-end forming versus single point ... |
Presentation
Preliminary study on the use of 3D printed biodegradable polymeric sheet for the manufacturing of medical prostheses by SPIF
(Elsevier, 2022)
Incremental Sheet Forming (ISF) and Fused Deposition Modelling (FDM) of polymers have both an edge over conventional ... |
PhD Thesis
Stretch and shrink flanging of AA2024-T3 sheet by single point incremental forming
(2021)
Flanging is a forming process widely used to increase the sti ness of sheet parts in industrial applications such as the ... |
Article
Tube Expansion by Single Point Incremental Forming: An Experimental and Numerical Investigation
(MDPI, 2021)
In this paper, we revisit the formability of tube expansion by single point incremental forming to account for the material ... |
Presentation
Revisiting flangeability in hole-flanging by single-stage incremental forming and conventional process
(PoPuPS (University of LiFge Library), 2021)
Recently, hole-flanging by single-stage incremental forming (SPIF) has been proposed as a suitable process to perform hole ... |
Presentation
Design for FDM of flexible tooling for manufacturing aeronautical components by incremental sheet forming
(IOP Publishing, 2021)
Nowadays, industrial production is required to reduce industrialization times and development costs for new products while ... |
Presentation
Numerical analysis of necking in stretch-bending based on modified maximum force criteria
(IOP Conference Series: Materials Science and Engineering, 2021)
The necking criteria based on the maximum force principle, such as the Swift and Hill necking models, have been extensively ... |
Presentation
On the manufacturing of highly-customized near net-shape medical implants using magnesium alloy sheet
(Elsevier, 2020)
The purpose of this work is defining a global methodology framework for the manufacturing of medical implants using Mg ... |
Article
On the Determination of Forming Limits in Polycarbonate Sheets
(MDPI, 2020)
By proposing an adaptation of the methodology usually used in metal forming, this paper aims to provide a general procedure ... |
Presentation
Hole-flanging of AA7075-O sheets: Conventional process versus SPIF
(Elsevier, 2020)
Recently, the research interest in hole-flanging for small and medium-sized batches has turned from conventional press-working ... |
Master's Final Project
Numerical analysis of formability and failure in tube inversion using i-Form
(2019)
El trabajo se basa en un análisis numérico de tubos de Aluminio AA6063-T6 deformados con punzones de diferentes radios ... |
Master's Final Project
Análisis numérico de la conformabilidad de chapa de AISI304-H111 en procesos de conformado convencional e incremental mediante DEFORM™-3D
(2019)
El principal objetivo de este proyecto es la creación de diversos modelos numéricos para placas de acero AISI304-H111 ... |
Presentation
Numerical study on the thickness homogenization in hole-flanging by single-point incremental forming
(Institute of Physics Publishing, 2018)
Incremental sheet forming is a novel technology that has significant benefits compared to conventional forming. However, ... |
Presentation
Experimental and numerical analysis of the flanging process by SPIF
(Institute of Physics Publishing, 2018)
This paper analyses the flangeability of AA2024-T3 sheets using single point incremental forming (SPIF). With this purpose, ... |
Article
On the Analysis of the Contact Conditions in Temporomandibular Joint Prostheses
(Hindawi Limited, 2018)
Temporomandibular joint replacement (TMJR) is a complex surgical procedure in which the artificial joints available must ... |
Article
Optimization of hole-flanging by single point incremental forming in two stages
(MDPI, 2018)
Single point incremental forming (SPIF) has been demonstrated to accomplish current trends and requirements in industry. ... |
Article
Revisiting Formability and Failure of AISI304 Sheets in SPIF: Experimental Approach and Numerical Validation
(MDPI, 2017)
Single Point Incremental Forming (SPIF) is a flexible and economic manufacturing process with a strong potential for ... |
Article
A Market-Based Analysis on the Main Characteristics of Gearboxes Used in Onshore Wind Turbines
(MDPI, 2017)
Even though wind energy is one of the most mature renewable technologies, it is in continuous development not only because ... |
Presentation
Preliminary investigation on homogenization of the thickness distribution in hole-flanging by SPIF
(Elsevier, 2017)
A drawback of the hole-flanging process by single-stage SPIF is the non-uniform thickness obtained along the flange. ... |
Presentation
Numerical explicit analysis of hole flanging by single-stage incremental forming
(Elsevier, 2017)
The use of Single-Point Incremental Forming (SPIF) technology in hole flanging operations using multi-stages strategies ... |
Master's Final Project
Metodología de evaluación de desviaciones geométricas 3D en piezas planas y volumétricas mediante Geomagic Control
(2017)
El objetivo principal de este trabajo es generar una metodología de escaneo mediante el uso de un escaner Geomagic Capture® ... |
Presentation
Recent Approaches for the Manufacturing of Polymeric Cranial Prostheses by Incremental Sheet Forming
(Elsevier, 2017)
This paper presents recent research experiences developed with the aim of manufacturing cranial prostheses in polymeric ... |
Final Degree Project
Análisis numérico en DEFORM-3D de deformaciones límite en conformado incremental mono-punto de chapas de acero AISI304-H111
(2016)
El principal objetivo de este proyecto es crear un modelo numérico para placas de acero AISI304-H111 conformadas mediante ... |
Final Degree Project
Análisis numérico de la conformabilidad de chapas de AA2024 - T3 en procesos de conformado incremental mono - punto usando DEFORM - 3D
(2015)
El método de los elementos finitos es un método numérico muy usado en ingeniería para la resolución de problemas complejos ... |
Presentation
Recent Approaches for the Determination of Forming Limits by Necking and Fracture in Sheet Metal Forming
(Elsevier, 2015)
Forming limit diagrams (FLD’s) are used to evaluate the workability of metal sheets. FLD’s provide the failure locus at ... |
Presentation
On the study of the single-stage hole-flanging process by SPIF
(Elsevier, 2015)
Recent studies show the capability of single-point incremental forming to perform successfully hole-flanging operations ... |
Article
Critical analysis of necking and fracture limit strains and forming forces in single-point incremental forming
(Elsevier, 2014)
Single-Point Incremental Forming (SPIF) is an emerging manufacturing process especially suitable to pro-duce small batches ... |
Presentation
Experimental Study on the Evaluation of Necking and Fracture Strains in Sheet Metal Forming Processes
(Elsevier, 2013)
In this paper the formability of AA2024-T3 metal sheets is experimentally analyzed. For this purpose, a series of ... |
Patent
Sistema de transmisión continuamente variable.
(Oficina Española de Patentes y Marcas , 2011)
Se trata de un sistema de transmisión continuamente variable (CVT), regulado por un mecanismo inercial que contempla un ... |
PhD Thesis
Desarrollo de un sistema de transmisión inercial continuamente variable para automoción
(2010)
En esta Tesis Doctoral se desarrolla un sistema de transmisión de potencia con aplicación en automoción. Se trata de un ... |
Article
Experimental study of impact on SMC composites used in the automotive industry
(Inderscience, 2007)
The signal from a piezoelectric sensor received by a data acquisition system was used to record the temporal evolution of ... |